Quote & Schedule

 

They are making a number of great points relating to How to Install a Bathtub as a whole in this content down below.

Installing a tub isn't specifically rocket science, however it does need strong plumbing, carpentry, and in some cases, tiling skills. Changing an old bath tub with a brand-new one is also a moderately challenging job. If the old bathtub is readily easily accessible, the job can move rapidly; if you have to open up a wall to remove the old bathtub and place the new tub, the job is much harder. In either situation, the project is within a residence handyman's skills, although you will need an assistant to vacate the old tub and also embeded in the new one. Make sure you have certified yourself for the work and are comfortable attempting it. Rather than employing a specialist to take over a halfway-completed task, it is better to consider using one before you begin. Chances are you may need a specialist plumber to make tube connections.
This article will certainly help you set up a new tub in your shower room if you have already purchased a new bathtub and don't need to transform the plan of your previous supply of water pipelines.
Your tools and product list ought to consist of the following:

 

• New Tub


• Hammer


• Pipeline Wrenches


• Prybar


• Shatterproof glass


• Degree


• Pliers


• Adjustable Wrench


• Putty Blade


• Screwdriver


• Cold Knife


• Measuring tape


• Pipeline Caps


 

Getting ready for the Setup

First of all, the sustaining structure supplied with the bathroom should be fitted (if called for) according to the maker's directions. Next off, fit the faucets or mixer to the bath tub. When fitting the tap block, it is necessary to make certain that if the tap features a plastic washing machine, it is fitted in between the bath as well as the taps. On a plastic bath, it is likewise practical to fit a supporting plate under the faucets unit to stop stress on the tub.
Fit the versatile faucet ports to the bottom of both taps using 2 nuts and olives (occasionally provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet with the hole in the bath. Utilize the nut provided by the supplier to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. Ensure you make use of all of the supplied washers.
Attach the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bath need to now be ready to be fitted in its last placement.

 

 

Removing Old Taps

If you need to change old faucets with new ones as a part of your installation, after that the first thing you should do is separate the supply of water. After doing so, activate the faucets to drain any type of water staying in the system. The process of removing the existing faucets can be fairly bothersome because of the restricted accessibility that is frequently the case.
Utilize a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipelines to the faucets. Have a fabric all set for the continuing to be water that will originate from the pipelines. Once the supply pipes have been gotten rid of, make use of the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to stop the solitary faucets from turning during this procedure. Once the faucets have actually been eliminated, the holes in the bath/basin will certainly need to be cleaned up of any old sealing substance.
Prior to moving on to fit the new faucets, contrast the pipeline links on the old faucets to the new faucets. If the old faucets are longer than the new faucets, then a shank adapter is required for the new faucets to fit.

 

 

Mounting the Bathtub

Utilizing both wooden boards under its feet, position the tub in the needed placement. The wooden boards are valuable in uniformly spreading out the weight of the bath tub over the location of the boards instead of concentrating all the weight onto four little points.
The following goal is to make sure that the tub is leveled all round. This can be attained by checking the spirit level as well as readjusting the feet on the tub up until the level reads level.
To install faucets, fit the bottom of the furthest flexible faucet connector to the appropriate supply pipeline by making a compression join; after that do the very same for the various other tap.
Switch on the supply of water as well as check all joints and new pipework for leakages and tighten them if required. Fill the tub and likewise examine the overflow electrical outlet as well as the typical electrical outlet for leakages.
Ultimately, deal with the bathroom paneling as described in the supplier's user's manual. Tiling and also securing around the bathtub needs to wait till the tub has actually been made use of at least once as this will resolve it right into its last placement.

 

 

Fitting New Taps

If the tails of the new faucets are plastic, after that you will need a plastic adapter to stop damage to the string. One end of the adapter fits on the plastic tail of the faucet and also the various other end supplies a connection to the existing supply pipes.
If you need to fit a monobloc, then you will call for reducing couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next off, position the faucet in the placing hole in the bath/basin ensuring that the washing machines remain in place between the faucet and the sink. Secure the tap in position with the producer given backnut. As soon as the faucet is safely in position, the supply pipelines can be connected to the tails of the faucets. The faucets can either be attached by using corrugated copper piping or with normal faucet connectors. The former type ought to be linked to the tap ends first, tightening only by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have been connected.

 

 

Tiling Around the Bath tub

In the location where the bathroom meets the ceramic tile, it is needed to seal the joins with a silicone rubber caulking. This is important as the fitting can relocate enough to split an inflexible seal, creating the water to permeate the wall in between the bathroom and the tiling, causing problems with dampness as well as feasible leaks to the ceiling below.
You can select from a selection of coloured sealants to assimilate your components and also installations. They are offered in tubes and cartridges, as well as can sealing voids approximately a width of 3mm (1/8 inch). If you have a larger void to load, you can load it with spins of soaked newspaper or soft rope. Bear in mind to constantly load the tub with water prior to sealing, to permit the movement experienced when the bathtub is in usage. The sealer can crack relatively early if you do not think about this motion before securing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are also conveniently available on the market. It is recommended to fit the floor tiles using water-resistant or water-proof glue as well as grout.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

I recently found that article on How to Install a Bathtub Yourself while browsing the search engines. In case you enjoyed our blog entry kindly do not forget to share it. We take joy in reading our article about How to Install a Bathtub Yourself.

Act now! Save later.